Every mold job we run includes the full sequence: camera inspection, containment, mechanical removal, antimicrobial treatment, sealing and verification. We do not sell a la carte cleaning that leaves mold behind. Here is what is covered on a standard visit, and what we quote separately if your system needs it.
We push a duct camera through the trunk and every branch line, plus check the plenum, coil pan and drain. You see the footage live. This is how we confirm where the mold is and whether the growth is surface-level or soaked into insulation.
A negative air machine with HEPA filtration runs at the main trunk for the entire job. This keeps dislodged spores from entering your living space. It is the single most important piece of equipment on a mold job and the one most competitors leave on the truck.
Every branch line gets brushed and whipped to break mold and debris off the duct walls. A HEPA vacuum pulls the loosened material out under negative pressure. We do not skip runs because they are hard to reach.
After mechanical cleaning, we fog the duct interior with an EPA-registered antimicrobial. This treats residual spores the brush could not reach. It is not a substitute for cleaning, it is the final step that makes the cleaning last.
We seal leaking joints and access ports with mastic so attic air stops pulling into the system. Then we tell you exactly what filter size and MERV rating to buy, and how often to change it, so the clean ductwork stays clean.
Mold in air ducts cleaning Murphy TX is the mechanical removal of fungal growth, spores and the organic food source they feed on from inside your HVAC ductwork, followed by sanitizing and moisture correction. It is not a spray-and-go job. We cut access ports at strategic points, run a rotary brush and air whip through every branch line, and pull the loosened debris into a HEPA vacuum while a negative air machine keeps spores from drifting into your living room. Flexible duct that is saturated usually gets replaced, not cleaned.
Murphy sits in Collin County where summer humidity parks above 60 percent for weeks and attic temps push past 140 degrees. That combination turns a small condensate leak or a poorly sealed plenum into a mold nursery fast. If you have been searching for mold in air ducts cleaning Murphy TX near me because your kids wake up congested every morning, or you have already booked duct mold remediation in Murphy Texas and want a second opinion, we will camera the system and show you what is actually growing in there before anyone quotes a number.
Every job follows the same five-stage sequence, whether it is a single-story Murphy Farms ranch or a two-system home in Stonebridge. You get a written scope before we start and a walkthrough when we finish.
Schedule
Call or book online — a real human picks up and confirms a 2-hour arrival window.
Diagnose
Licensed tech inspects on-site, then walks you through the cause and your options.
Fix
The job is completed to code and done right the first time — no shortcuts, no surprises.
Guarantee
Every job backed by a written workmanship warranty — and we stand behind it.
Negative air machine
Creates negative pressure at the main trunk so dislodged spores cannot escape into living space. Runs for the entire job and is the backbone of our containment setup.
HEPA vacuum
Captures mold, dust and debris pulled from the duct walls. HEPA filtration traps particles down to 0.3 microns, which is smaller than most mold spores.
Rotary brush and air whip
Mechanically scrubs mold off duct walls and whips it into the airstream for capture. We run both on every branch line because each reaches surfaces the other misses.
Duct camera
Lets us see inside the trunk and branches before and after cleaning. You watch the footage with us, so there is no guesswork about what was found or what was removed.
Duct fogger
Applies EPA-registered antimicrobial evenly across the duct interior after mechanical cleaning. Fogging reaches corners and seams the brush cannot touch.
Compressed air nozzle
Used on coil fins and cabinet surfaces to blow loose debris into the HEPA airstream. Helps us clean the air handler without damaging delicate fins.
Rotobrush and Nikro equipment
Our primary cleaning platforms. Rotobrush handles the branch lines, Nikro handles the larger trunk runs and heavy debris. Both are industry-standard for professional duct cleaning.
NADCA ACR Standard
We follow the NADCA Assessment, Cleaning and Restoration standard for every mold job. That means camera assessment first, containment during cleaning, and verification after. It is the difference between remediation and a surface wipe.
Source correction
Cleaning mold without fixing the moisture that fed it is a temporary fix. We check the coil pan, drain line, plenum seams and duct insulation, and we tell you exactly what needs repair so the growth does not return next cooling season.
Containment-first setup
Negative air and register sealing go up before any brush touches the ductwork. This is the step that protects your furniture, your air quality and your family during the job. We do not start cleaning until containment is verified.
Camera verification
After cleaning, we re-camera the trunk and branches and compare to the pre-job footage. If any visible growth remains, we keep working. You get the after footage before we pack up.
01
What we do: We treat this as an emergency. Containment goes up first, then we camera the system to see how far the moisture traveled. Saturated flexible duct gets replaced, the rest gets cleaned and sanitized, and we check the coil pan and drain line for standing water.
→ The system is dry, clean and safe to run again, usually within one day. You get documentation for your insurance claim if you are filing one.
02
What we do: We run a NADCA Certified Ventilation Inspector (CVI) level inspection, document everything on camera, and provide a written remediation scope. After the work, we re-camera and give you a clearance report the buyer's agent can attach to the file.
→ The deal moves forward with a documented remediation instead of a price reduction. Most closings we support clear within a week of the inspection.
03
What we do: Post construction duct cleaning is the right call here. Drywall dust is alkaline and holds moisture, which is exactly what mold needs. We run the full mechanical clean, sanitize, and replace the filter with a fresh one sized to the system.
→ The new construction smell clears out, the ducts are clean, and you start the warranty period with a system that is not already contaminated.
04
What we do: Pet dander is organic and holds moisture, so it feeds mold. We pull the hair and dander out with the rotary brush and HEPA vacuum, then sanitize. If the growth is heavy, we may recommend replacing the worst branch runs.
→ Less pet odor, fewer allergy symptoms, and a duct system that is not doubling as a dander reservoir. We give you a filter change schedule that fits a multi-pet home.
Murphy sits in Collin County where the cooling season runs from April through October and attic temperatures regularly exceed 140 degrees. That heat drives condensation inside ductwork, especially where flexible duct runs through unconditioned attic space. Add the spring pollen load and the summer humidity, and you have ideal conditions for mold growth any time a duct seam leaks or a coil pan overflows. Most of the homes we service in Murphy were built between the 1990s and the 2010s, and many still have original flexible duct in the attic. That material has a lifespan, and when it tears or compresses, it traps moisture and feeds mold. We see the same pattern in Maxwell Creek, Stonebridge and Willow Wood: a small condensate leak, a few weeks of summer heat, and suddenly the whole trunk smells musty. If you are searching for mold in air ducts cleaning 24/7 Murphy TX because the smell showed up over a weekend, call us. We run emergency and after-hours scheduling and we keep containment equipment on every truck so the job can start the same day.
Maxwell Creek
Many homes here have long attic duct runs with original flexible duct. That material compresses over time and traps moisture, which is where we find most of the mold growth in this neighborhood.
Stonebridge
Larger two-system homes here often have one air handler in the attic and one in a closet. Both need inspection, because mold in one system can go unnoticed while the other runs clean.
Murphy Farms
Single-story ranches with slab foundations. Slab leaks are less common than attic moisture, but when they happen, ductwork in the affected area needs immediate attention.
Timber Creek
Mature trees mean heavy spring pollen, which feeds mold when it settles in ductwork. Homes here benefit from a spring cleaning before the cooling season starts.
Parker Road Corridor
Mix of residential and commercial. We run both residential and commercial mold jobs here, often scheduling commercial work after hours to avoid disrupting business.
Attic temperatures above 140 degrees in summer
Heat drives condensation inside ductwork, especially where insulation is thin or the duct runs close to the roof deck. This is the single biggest driver of mold growth in Murphy homes.
Humidity above 60 percent from May through September
High outdoor humidity means any air leak into the duct system brings moisture with it. Sealing joints and plenum seams is as important as cleaning on a Murphy mold job.
Original flexible duct in 1990s and 2000s homes
Flexible duct has a service life. When it tears, compresses or gets wet, it holds moisture and feeds mold. We replace saturated sections rather than trying to clean them.
Spring pollen load from mature trees
Pollen is organic and holds moisture. When it settles in ductwork, it becomes a food source for mold. A spring cleaning before the cooling season prevents that buildup.
Mold in ductwork shows up in predictable ways. If any of these sound familiar, a camera inspection will tell you whether remediation is the answer or whether something else is going on.
Problem
The smell is spores and microbial volatile compounds cycling into every room. Ignoring it usually means the growth spreads to more of the duct system and eventually into the air handler cabinet.
Our Fix
We camera the system, locate the growth, and remove it mechanically. Then we treat the duct interior with an EPA-registered antimicrobial and seal the moisture source. Most customers notice the odor is gone the same evening.
Problem
Overnight is when the system runs longest and spores settle into bedrooms. Chronic congestion, headaches and allergy flare-ups often trace back to mold in the supply runs feeding the bedrooms.
Our Fix
Mold in air ducts cleaning Murphy TX removes the spore source, and we can pair it with an air duct cleaning for allergies upgrade: higher-MERV filtration and a coil treatment to keep the system clean between visits.
Problem
Dark staining at the register usually means mold is growing on the duct boot or the ceiling material around it. Left alone, the growth works into the duct insulation and the ceiling drywall.
Our Fix
We inspect the boot, the branch line and the surrounding ceiling. If the duct section is contaminated, we cut it out and replace it. If the ceiling material is affected, we tell you so you can get it handled by a drywall pro.
Problem
Mold and debris restrict airflow, which raises static pressure and forces the compressor to run longer. Homeowners often blame the utility rate when the real problem is a choked duct system.
Our Fix
After cleaning, we measure static pressure at the return and compare it to the pre-job reading. Restored airflow usually means shorter runtimes and a lower bill the following month. We show you the numbers.
Mold in ductwork does not stay in the ductwork. It rides every air cycle into bedrooms, kitchens and home offices. Here is what changes once the growth is physically removed and the moisture source is corrected.
Musty odors gone
That damp basement smell coming from your registers is usually mold colonizing the duct insulation or the evaporator coil pan. Once we remove the growth and sanitize the interior surfaces, the odor stops cycling through the house. Most customers notice the difference the same evening the system goes back on.
Fewer allergy flare-ups
Mold spores are small enough to bypass standard filters and land deep in the lungs. After mold in air ducts cleaning Murphy Texas, homeowners with seasonal allergies often report fewer morning headaches and less sneezing. We also upgrade you to a properly sized HEPA filter so the clean ductwork stays clean.
Lower energy bills
A moldy, debris-packed duct system restricts airflow, which forces your compressor to run longer to hit the thermostat setpoint. Cleaning the runs and sealing leaking joints typically restores static pressure and trims runtime. In a 2,400 square foot Murphy home, that often shows up as a measurable drop on the next electric bill.
Longer HVAC life
Mold growth usually means moisture, and moisture kills blower motors, rusts cabinet panels and shortens compressor life. Handling the mold early protects the equipment you already paid for. We document coil condition during every moldy duct cleaning Murphy visit so you know whether the air handler needs attention too.
Google ★★★★★4.9
PureBreeze Path handled mold in our ductwork after a roof leak. They showed us the camera footage before and after, which no other company offered. The crew was on time, clean and respectful of our home. The musty smell was gone the same day. Highly recommend for anyone in Murphy dealing with this.
Yelp ★★★★★4.8
We had three companies quote our mold remediation and PureBreeze Path was the only one that talked about containment and negative air. They spent most of a day on the job and the difference in air quality was obvious. Fair pricing and no pressure to add services we did not need.
BBB ★★★★★5.0
Professional from the first phone call. They scheduled a camera inspection within two days, explained exactly what they found, and gave us a written scope. The work was done on time and on budget. Our allergies have improved noticeably since the cleaning.
Google ★★★★★4.9
We manage a commercial property in Murphy and had mold around the ceiling registers in one unit. PureBreeze Path worked after hours so we did not lose a business day and documented everything for the landlord. Clean work and good communication throughout.
PureBreeze Path has been cleaning and remediating ductwork in Murphy since 2022. In that time we have handled hundreds of residential and light commercial systems across Collin County, from single-family homes in Maxwell Creek to retail buildouts along the Parker Road Corridor. Our technicians hold NADCA Air Systems Cleaning Specialist (ASCS) credentials and follow the ACR standard for assessment, cleaning and restoration of HVAC systems. We carry Texas HVAC licensing, OSHA 10 cards and IICRC certification, and we treat every job like the homeowner is standing next to us watching, because usually they are.
Real answers to the questions we hear most often from local homeowners and property managers.
Our core local Airduct cleaning service covers the full system, not just the visible registers. When we handle mold in air ducts cleaning for a Murphy home, we clean the trunk, branches, plenum and coil cabinet in the same visit so nothing gets missed.
View local Airduct cleaningIf you searched Airduct cleaning near me and landed here, you are in the right place. We serve all of Murphy and 75094 with same-week scheduling. Our trucks carry everything needed for a full mold job, so we rarely need a second trip.
View Airduct cleaning near meMold does not wait for business hours, and neither do we. Our 24/7 Airduct cleaning line handles after-hours calls for musty odors, post-leak contamination and emergency situations. Call (855) 948-0345 any time and we will dispatch the next available crew.
View 24/7 Airduct cleaningSame Day Airduct cleaning is available for most Murphy addresses when you call before noon. That matters when a slab leak or roof leak has just soaked your ductwork and mold is starting to colonize. Fast action limits how much duct has to be replaced.
View Same Day Airduct cleaningEmergency Airduct cleaning covers the situations that cannot wait: sewage backups into ductwork, storm water intrusion, or a mold bloom discovered right before a home sale. We prioritize these calls and bring containment equipment to keep spores out of living space.
View Emergency Airduct cleaningOur commercial Airduct cleaning service handles restaurants, offices and retail spaces along the Parker Road Corridor and Murphy Marketplace. Mold in a commercial system is a liability issue, so we document everything and schedule work around your operating hours.
View commercial Airduct cleaningCall (855) 948-0345 or email [email protected] and we will get back to you fast. Our phones are answered 24/7 for emergencies, and regular scheduling runs Monday through Friday, 8 a.m. to 6 p.m. If you are in Murphy, we can usually get a tech to your door the same day.
Phone
(855) 948-0345Address
410 W Farm to Market 544, Suite 102 Murphy, TX 75094 USA, Murphy, Texas
Hours
Mon–Fri: 7AM – 7PM
Sat: 8AM – 4PM
Sun: Emergency Only
24/7 Emergency Available
